However if you wish to supply us with coated panels it is important that the thickness and composition of the substrate is such that it can be deformed and the substrate itself does not crack under test. If we are to determine the largest mandrel that causes failure, we need 15 panels for each coating. Perfectly flat with a non-textured test surface Weight less than grams We can cut larger panels to size for you or, if you wish, we can prepare the panels. Axalta opens new India headquarters 10th May Read more. This guide covers the selection and use of procedures for testing water-reducible coatings, both pigmented and clear, utilizing synthetic lattices, synthetic resin emulsions, or water-reducible alkyds.
|Published (Last):||2 February 2006|
|PDF File Size:||10.46 Mb|
|ePub File Size:||11.97 Mb|
|Price:||Free* [*Free Regsitration Required]|
Kegal This guide covers the determination of the abrasion resistance of textile fabrics using the rotary platform, double head tester RPDH. Work Item s — proposed revisions of this standard. Determination of Surface Drying Time. This Standard is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products. If you specify the mandrel diameter, we need 3 panels.
This work is not carried out to any international This Japanese Industrial Standard specifies the testing methods for the evaluation of general characteristics of woven fabric foundation cloth.
BS EN ISO This document specifies two alternative test methods to determine the resistance to wear of lacquered wood floorings and one to test the elasticity of the lacquer.
Mechanical property of film — Section 8: If you specify the mandrel diameter, we need 2 panels. This document sets forth recommended minimum performance standards for vinyl and other polymeric films, plain and printed, which are used as in-ground swimming pool liners.
BS C2, ISO Scope and Field Application BS C2 and ISO are alternative names for the same method which is intended for the determination of the surface drying characteristics of a paint or varnish film which dries by reaction with air or by a chemical reaction of its components.
It is important to us that you purchase the right document. This International Standard specifies the method for measuring abrasion of laminate floor covering elements.
Description of a method that measures the ability of a coated surface to resist abrasive wear-through to the underlying substrate by assessing the resistance to liquid paraffin fat in the abraded area. This SAE recommended practice covers the requirements for rubber floor mats made from five types of rubber compound as required by the physical property requirements of the application. Follow these links to find other Standards similar to the one you are viewing. We recommend that you check the kso of the publishers of the international document before making a purchase.
BS EN ISO and BS E6 jso alternative names for the kso method which is used to assess the resistance of a dry film of paint, varnish or related product to separation from a substrate when a right-angle lattice pattern is cut into the coating and penetrates through to the substrate. None of the methods are suitable for measuring metallic coatings but some can be adapted for the measurement of detached organic films. BS EN Surfaces for sports areas — Determination of resistance to abrasion of non-filled synthetic turf This document describes a method for the determination of the wear resistance of a non-filled synthetic turf surface using an abrasive wheel under laboratory conditions.
International Classification for Standards ICS is an international classification system for technical standards.
The test piece can be as small as 10 x 10 on any sio rigid substrate. Determination of resistance to abrasion.
We normally supplement this method with an in-house determination of recoatability. Specifies requirements for safety glass for installation as windscreens, other windows, or as partitions in motor vehicles and trailers. This specification covers prefaced concrete masonry units with the exposed-to-view-in-place surfaces covered at the point of manufacture with resin, resin and inert filler, or cement and inert filler to produce a smooth resinous tile facing.
BS AU Part The purpose of this test is to quantify the haze, luminous transmittance, and abrasion resistance properties of the primary lens material of a full facepiece RPD.
Perfectly flat with a non-textured test surface Weight less than grams We can cut larger panels to size for you or, if you wish, we can prepare the test panels. This specification does not address, and therefore is not applicable to, ground-face concrete masonry units that are manufactured by grinding a thin layer off the surface of a io masonry unit to expose aggregates within and polishing to produce smooth, architectural finish.
Determination of Properties The test measures the ability of the decorative surface of the sheet under test to resist abrasive wear-through to the sub-layer. See tests 12 and BS EN ISO and BS E5 are alternative names for the same method which is used to assess the hardness of a dry film of paint, varnish or related product measuring how it reduces the oscillation amplitude of a pendulum. This test method covers the laboratory procedure for determining abrasion resistance of resilient flooring using an abrader with a grit feeder.
They should be x x at least 3 mm. This standard sets out a method for the determination of the abrasion resistance of textile fabrics applicable to all textile fabrics including coated and laminated fabrics, a method for wet testing is also specified. The dimensions for crack testing should be x mm. LAT Hard Anodizing This method covers the requirements for anodization of aluminum and oso alloys MIL-AF 1 Military Specification — Anodic Coatings for Aluminum and Aluminum Alloys This specification covers the requirements for six types and two classes of electrolytically anodic coatings on aluminum and aluminum alloys for non-architectural applications.
Sample Requirements We need 3 coated panels for each coating. Related Posts.
ISO 7784-2 PDF
EVS-EN ISO 7784-3:2016